handwheel
美 
英 ['hændwi?l]
英漢解釋
例句
Carefully remove the handwheel. Slight tapping with a mallet may be required, but do not change the valve stem position.
小心拆卸手輪。如果需要，用木槌輕輕敲打，但是不要改變閥桿位置。
Turn the handwheel to move the needle bar up to its highest position .
轉動飛輪，把針桿上升到最高部位。
This dimension must be at least twice the dimension from center line to handwheel.
這個尺寸必須至少為從閥門中心線至手輪距離長度的兩倍。
The handwheel can be removed and repositioned any of six positions around the stem.
手輪可以拆卸并重新定位在環繞閥桿的六個位置中的任何一個位置上。
The amount of tactile feedback to the driver through the handwheel may also be electronically controlled.
通過方向盤反饋到駕駛員的感官量也是通過電子控制。
This includes variable effort assist and handwheel return characteristics which may be tuned to a desired feel and responsiveness.
這包括可變助力和方向盤回位特性，這都可調諧到一個理想的感受和反應能力。
If the connection is to be made by soldering, turn the handwheel to the fully open position before applying heat.
如果是焊接連接，則在加熱之前要把手輪旋轉到全開的位置。
The handwheel, When the handwheel left rotates, the nets yarn at a state, when the handwheel right when rotating gauze is flabby condition.
手輪；當手輪向左旋轉時，網紗處于張緊狀態，當手輪向右旋轉時網紗處于松弛狀態。
The valve is equipped with a hand-wheel. The handwheel does not house a spring and does not wiggle or pivot.
閥門配有手輪。手輪內沒有裝彈簧，不會扭動或轉動。
Possible handwheel orientations are shown in the figure to the right below.
可能的手輪方位如下圖右側所示。
Beneath the handwheel is one set of wrench flats on a nut threaded into the valve body.
在手輪下面，在一個旋進閥體的螺母上面是一套扳手面。
Remove handwheel and turn indicator sleeve by grasping the handwheel and pulling away from the valve body along the stem.
拆卸手輪，并通過抓住手輪旋轉指示器套筒，將其沿著閥桿從閥體內拉出。
Hammerblow handwheel adapters can be furnished with handwheel or chainwheel construction.
錘擊手輪接合器可以配置在手輪或鏈輪結構上。
Single pulling the handwheel through tooth synchronous transmission chain, ensure single-side chuck pull synchronization.
單面拉網手輪通過齒鏈條同步傳遞動力，保證單面夾頭拉力同步。
closes the right eye, rotates the middle axle focusing handwheel, looks until the left eye by the clear scenery.
閉上右眼，轉動中軸調焦手輪，直到左眼看以清晰的景物為止。
Operating Principle: The diaphragm valve is a handwheel-operated valve, utilizing a two-piece stem separated by non perforated diaphragms.
運轉原理：膜板閥是一種手輪型閥門，它采用兩個由非穿孔橫膈膜隔開的閥桿。
FEATURES: adopted cricoid feed foot and driving handwheel . Not wrinkling when sewing thin materials. With uniform and pleasing outline.
采用輪型送步牙及驅動式輪線，縫制厚薄物品不起皺，縫目均勻美觀。
Low Profile Gear Operator features high efficiency worm gear drive with built-in position indicator and high impact polypropylene handwheel.
低高度的齒輪操作機構配置高效蝸輪驅動結構，并內置位置指示器和高強度抗沖擊的聚丙烯手輪。
This is achieved through the use of a handwheel and a screw, around which a nut fixed to the quill is engaged.
這通過使用手輪和螺桿來達到，與螺桿嚙合的是一固接在套筒軸上的螺母。
tied-diaphragm valve is a handwheel-operated valve, utilizing a two-piece stem connected through the diaphragms.
束縛隔膜閥是采用通過橫膈膜連接的兩個閥桿的手輪型閥門。
The disc position corresponds with the decimal indicator viewed through the handwheel window.
閥瓣位置與十進制指示器相一致，并可通過手輪上的窗口一覽無遺。
This accessory provides extension of the handwheel to allow remote operation - normally from above .
這個附件提供手輪加長件，通常便于在閥門上方進行遠程操作。
panel draws the corresponding hairline in the gate bottom, takes place initially the gate module, undulates the handwheel.
在啟閉機底板上畫出相應的十字線，將啟閉機組件初步就位，搖動手輪。
Complete valve data: figure number and valve size. Dimension from valve centerline to top of extension stem handwheel.
完整的閥門參數：型號和閥門通徑。從閥門中心線到閥桿加長件頂部手輪的尺寸。
Reasonable care in operation (e. G. , Avoidance of overtightening of the handwheel).
操作時合理的小心謹慎（例如，避免手輪過緊）。
To order, specify handwheel actuator code, and add extension description as second line information.
如果要訂購加長件，請指定手輪執行器代碼，并在第二行加上加長件的描述信息。
Handwheel to adjust conveyor belt up and down.
手動搖輸便于調節輸送帶高低。
To order, specify description and extension length from center line of valve to top of handwheel or nut.
訂購時，注明描述信息和從閥門中心線至手輪頂部或螺母的加長長度尺寸。
Carefully remove the handwheel and turn indicator sleeve assembly, leaving the valve at its balance set point.
小心拆卸手輪，并旋轉指示器套筒總成，將閥門保留在它的平衡設置點上。
To order handwheel or chainwheel actuators, add the appropriate order code to the basic valve order code.
如果要訂購手輪或鏈輪執行器，需要在主閥門訂購代碼的基礎上添加適當的執行器訂購代碼。
To order, specify description and extension length from center line of valve to handwheel.
訂購時，注明描述信息和從閥門中心線至手輪的加長長度尺寸。
Valves supplied with hammerblow handwheel as a standard.
錘擊手輪是閥門的標準配置。
Regulation is accomplished by rotating the handwheel clockwise .
規則要求按順時針方向旋轉手輪。
Reinstall the handwheel in the correct orientation so that the original setting is indicated and secure with the retaining bolt.
按照正確的方向重新安裝手輪，使得原先的設置能夠顯示，并用固定螺栓加固。
Specify required extension length from centerline of valve to handwheel.
注明從閥門中心到手輪的所需加長件的長度。
1 rotates the handwheel , the inspection gate body in the doorframe whether about skids nimbly, wedges tightly whether arrives.
1轉動手輪，檢查門體在門框中是否上下滑動靈活，楔緊是否到位。
Removal of handwheel without affecting the position of valve ( closed or open ) .
手輪可拆卸，不影響閥門的開關位置（關閉或開啟）。
The roller surface accent wide installs to uses the lead screw handwheel adjustment.
輥面調寬的對中裝置采用絲桿手輪調節。
In valves, aluminum is mainly used as an exterior trim component such as a handwheel or identification tag.
在閥門上，鋁主要作為外部裝飾材料裝飾部件，如手輪或銘牌等。
To order, specify handwheel actuator code, and add floorstand description as second line information.
如果要訂購位置指示地軸承架，請指定手輪執行器代碼，在第二行增加地軸承架的描述信息。
