roundness
美 [ra?ndn?s] 
英 [ra?ndn?s]
同義詞
英漢解釋
例句
The cross section shapes of the pits are same with that of the lock hole of the intramedullary nail, which are roundness or ellipse.
凹坑的橫截面形狀和髓內針鎖孔的橫截面形狀相同，橫截面形狀是圓形或者是橢圓形。
He gave us the results in round numbers, but their roundness didn't affect the point he was making.
他給我們的是整數結果，但其取整不影響他提出的論點。
Numerical results showed that on this assumed condition, the smaller the tolerance of roundness is, the longer the fatigue life of hole.
數值模擬結果表明，在此假定條件下，孔的圓度公差越小，孔的疲勞壽命越大；
The straightening process is generally used to eliminate the longitudinal bending and the roundness error of the rolled seamless steel pipe.
為了消除無縫鋼管軋制后的縱向彎曲及圓度誤差，一般要采用矯直工藝。
NON-ROTATING STEM Non-rotating stem has close roundness and straightness tolerances and is burnished for a superior finish.
不旋轉閥桿不旋轉閥桿具有精密的圓度和平直度公差，并且經過拋光達到極高的拋光度。
Researches are made to find out the active tracing measurement strategy of crankshaft roundness error during non circular grinding process.
采用非圓磨削加工曲軸可在一次裝夾完成主軸頸和連桿頸的磨削。
Her thighs, too, they used to look so quick and glimpsy in their female roundness, somehow they too were going flat, slack, meaningless.
她的大腿也是一樣，從前富有女性的圓滿的時候，是那樣的靈活而光輝，現在卻是平板、馳松而無意義了。
A new method of auto measuring the roundness error by means of the linear CCD (charge coupled device) is proposed.
提出一種應用線陣CCD自動測量圓度誤差的新方法。
He still had just a hint of childish roundness left around his chin.
他的下巴依然留著一點嬰兒肥的痕跡。
This method opens up the possibility for measuring sphericity using roundness measuring instrument.
該法為圓度儀測量球度開辟了一條新途徑。
The radial run-out deviation is composed of the coaxiality deviation and parts of the roundness deviation.
徑向跳動偏差的由同軸度偏差和零件的圓度偏差構成。
for measurements of rotational parts of coaxiality, roundness, symmetry, pulse volume.
用于回轉類零件的同軸度、圓度、對稱度、跳動量的測量。
This paper analyses roundness error by means of minimum zone law, and then a mathematics model is put forward.
在直線度、平面度公差判定的最小包容區域法中提出一個新的、快速的實施方法。
To support the principle of triangulation, etc. , the rolling process, the workpiece can improve roundness, concentricity, perpendicularity.
以等三角支撐原理，進行滾壓加工，可提高工件真圓度、同心度、垂直度。
Determine out-of- roundness by comparing the difference between each measurement.
比較每個測量的不同，決定失圓。
The marbles shown here give a sense of smoothness, hardness, and roundness; the shells give a sense of texture.
這里展示的大理石雕刻品給了一種光滑、堅硬、圓形的感覺，而貝殼則給了一種紋理的感覺。
For higher depths of cut a decreasing tendency for the roundness can be observed although process forces increase.
隨著切削深度的加大，圓度呈下降趨勢，盡管切削力增加了；
The principle of the measuring roundness error system used the equal thickness interference and CCD image-processing system is expatiated.
闡述了利用等厚干涉，通過線陣CCD圖像處理系統自動測量圓度誤差的測量原理。
In Design and architecture, we are dealing with roundness and curves, with everything in reference to the body.
在設計與建筑中，我們要面對的是圓形與曲線，涉及到的一切都和身體有關。
Moreover, the business card printing and membership card-making Ink viscosity temperature variance is large, on the rollers of roundness.
另外在制卡和會員卡制作洋油墨黏度施溫度感化改變較不小，差墨輥的圓整度請求較矮。
Her hairstyle exaggerates the roundness of her face.
她的發式使她的臉形顯得更圓。
Methods: The process was studied by orthogonal experimental design with pill weight variation and roundness as the detective marker.
方法：采用正交實驗法，以丸重差異和圓整度為考察指標，對影響清開靈滴丸滴制過程的因素進行考察。
True Position cannot be changed at grinding only size, roundness and micro finish.
打磨時除尺寸，圓度和微觀表面發生變化外，基準位置不變。
Wall Thickness. The actual wall thickness of a tubular product caused by variations in pipe roundness, cross-section or eccentricity .
壁厚。由于管子圓度、截面或偏心等因素變化而導致的管材實際壁厚。
The proposed tolerance system is complementary to the existing geometrical roundness tolerance system.
提出應以統計圓度公差作為幾何圓度公差的補充與發展。
The research of roundness measuring technique of steel tube is an important problem in the manufacture.
鋼管圓度檢測技術的研究是目前生產和使用過程中所面臨的一個重要課題。
Evolution is as firmly established a scientific fact as the roundness of the Earth.
進化是一個既定的科學事實就好比地球是圓的一樣。
It is feted by the consumption of mooncakes, the roundness of the sweet pastry symbolising the union of family members.
人們慶祝的方式是吃月餅，這種甜點圓圓的形狀象征著家人團聚。
The roundness of particles continuously large ns and the spatial arrangement of particles becomes compacted as water content advances.
隨著制樣含水量的提高，顆粒圓度不斷增大，其空間排列變得緊密；
Precision stem and packing chambers. Straightness, roundness and fine finish of stem and packing chamber wall are essential.
精密加工的閥桿和填料腔。閥桿和填料腔壁的平直度、圓度和表面光潔度是最基本的要求。
Aluminum pipe precise forming technology makes the ultrasonic welded Aluminum pipe size precise and roundness good.
鋁管精密成型技術，使超聲波焊接的鋁管尺寸精確、圓度好。
To evaluate the quality of damper connecting rod, roundness and straightness are important technical indices.
圓度和直線度是評價汽車減振器連桿質量的關鍵技術參數。
Bead roundness, sphericity, smooth finish and bright degree, depends entirely on the polishing process.
圓珠的圓度、毬度、光潔度以及亮麗程度，完全在于打磨拋光工序。
gravel roundness increased along the river by analyzing the field data in baishahe river , a tributary of jinjiang river.
通過分析岷江支流白沙河的實測資料得出，卵石圓度沿程加大。
The wrong-way-a roundness of these requests always puzzles me.
這些找不著方向的問題總是讓我困惑不已。
In this paper, a roundness measurement method applying the multiple bearing technology is provided for practice.
從測量實踐出發，總結出一種利用多次定位技術進行圓度測量的方法。
significantly improves part quality in warpage, roundness, flatness and dimensional stability, reduces molded-in stress MuCell?
可改善產品的翹曲，同心度，平面度及尺寸的穩定性和產品內應力。
The fish balls produced by the equipment, with low density, good roundness, and surface smooth.
該設備生產的魚丸，具有密度小、圓度好、外表光滑等特點。
Shape dynamics enables several options to handle randomness of Size, Angle, Roundness and Flip Axis values.
形狀動態，使多種選擇來處理大小，角度，圓度和翻轉軸值的隨機性。
The spinning force increases with increasing the reduction of blank radius, the feed rate and the roundness radius of roller.
旋壓力隨壓下量、進給比、旋輪圓角半徑的增加而增加；
