J-integral

J-integral

美 　英

• 網絡J積分；庫侖積分

例句

The methods and processes can be used to analyze J-integral of tee with longitudinal through-wall crack by ABAQUS.

因此，可按該方法和步驟應用ABAQUS程序計算含裂紋三通的J-積分。

A systematical calculation was conducted for the J integral crack parameter of a welded joint using the finite element method.

采用有限元方法對焊接接頭的斷裂參量J積分進行了系統計算。

In composites with low adhesion level between matrix and glass beads, the critical J-integral value diminished due to the presence of PET.

在與基體之間的附著力和玻璃珠低層次復合材料，臨界J積分值減少由于PET的存在。

At last the K1 of elastic plane with different thickness was calculated by the theory of J-integral.

最后應用J積分理論計算了有限厚度的板在剛性壓頭作用下的應力強度因子。

Because the integral relates with the path, one special computer formula of J -integral is given in the last.

由于積分與路徑有關，最后僅給出了一種特殊路徑下J積分的計算公式。

The results indicate that the K1 by J integral was in accord with the theoretical value.

數據結果表明，由J積分方法計算的K，與理論值一致。

The results indicate that multi-site damage have a great influence on the J integral values.

結果表明，多部損傷對焊接接頭結構強度造成了極其惡劣的影響。

Path-Independent J-Integral and Its Dual Form in Elastic-Plastic Solids with Finite Deformation

有限變形彈性體J積分守恒及其對偶形式

Finite Element Numerical Analysis of J-Integral Values of Welded Joint Containing Different Location Cracks

不同裂紋位置焊接接頭J積分有限元數值分析

Cyclic J-integral Engineering Assessment Method for Remaining Fatigue Livetime of Crack Structure

含裂紋結構剩余疲勞壽命循環J積分工程評估方法

J-integral Finite Element Analysis of Fracture Failure of Submarine Cone-cylinder Pressure Shell Structure

潛艇耐壓錐柱結合殼斷裂失效J積分有限元分析

Calculations of Three Dimensional J-Integral by Surface Integral Method in Finite Element Analysis

三維J積分有限元分析的曲面積分法

J-integral estimation of circumferential-cracked round bars subjected torsion

扭轉載荷下帶環狀裂紋圓棒的J積分的評價

J-Integral Study of Elbow with CircumferentialThrough-Wall Crack

含環向貫穿裂紋彎管的J積分研究

Crack Opening Displacement and J-integral Calculation of Fracture Process Zone Length

斷裂過渡區長度張開位移和J積分的計算

Numerical Finite Element Analysis of J-integral Fracture Parameters for Welded Joints

焊接接頭J積分斷裂參量的有限元數值分析

Standard Test Method for J-Integral Characterization of Fracture Toughness

斷裂韌性的J-綜合特性的標準測試方法

Discussion on determination of J-integral and comparison of different test standards

關于J積分測定方法的比較及相關問題的討論

Complex Function Method On J-integral of Mixed Mode Crack-Tip for Anisotropic Fiber Composite Plate

含裂紋復合材料板J積分的復變函數方法

The Progress of Engineering Evaluation Method of J-integral in Structure Containing Defect

含缺陷結構J積分工程估算方法研究進展

Theoretical Research of Crack Tip J-integral for Orthotropic Composite Plate

正交異性復合材料板裂紋尖端J積分的理論探討

The J-Integral Criterion of Interface Fracture in Composite Laminates

復合材料層壓板界面裂紋的J積分判據

Calculation of three-dimension elastic-plastic based J-integral

基于三維效應的彈塑性J積分計算

The J-Integral Solution of Circumferential Surface Cracked Pipe

周向表面裂紋管道的J積分解

Research on J-integral of Mixed Mode Crack-tip for Anisotropic Fiber Composite Plate

各向異性復合材料板混合型裂紋尖端的J-積分

Experimental Study on the Effect of Mechanical Heterogeneity on Dynamic J-integral for Welded Joints

力學不均勻性對焊接接頭動態J積分影響的實驗研究

Conservation Law and Application of J-Integral in Multi-Materials

J積分在多層介質中的守恒性和其應用

Numerical Investigations to J-integral in Cracked Weldment Containing Damage Based on Finite Element Method

含損傷焊接接頭裂紋體J積分的有限元數值研究

Effect of Higher Order Terms in Eigenfunction Expansion Forms on J-Integral

特征展開式中高階項對J積分的影響

Computation of J-Integral With Finite Element Method

有限元方法計算J積分

Calculating and analyzing of J-integral in the center-crack ed panel

三維中心裂紋板中J積分的計算及分析

On J-Integral of Mode I Crack-Tip for Anisotropic Fiber Composite Plate

各向異性板I型裂紋尖端的J-積分

The Analysis of J-integral in Anisotropic Elastic Solids

各向異性彈性體中的J積分分析

On Crack-Tip J-Integral for Orthotropic Composite Plate

關于復合材料單層板裂紋尖端的J積分

Research of J-integral for crack parallel to interface

平行界面裂紋J積分的研究

Study on three-dimensional cracked J-integral

三維裂紋J積分研究

New Cyclic J-Integral for Low-Cycle Fatigue Crack Growth

描述低周疲勞裂紋擴展速率的循環J積分新參量

J-integral of Surface Crack in Overmatched Joint

高組配焊接接頭表面裂紋J積分試驗研究