hot-forging

hot-forging

美 　英

• n.熱鍛

英漢解釋

n.

1. 熱鍛

例句

To improve and stabilize the service life of hot-forging die fabricated by cast die steer, the failure modes and mechanism were analyzed.

為了穩定和提高精鑄熱鍛的使用壽命，研究了其失效形式和機理。

After analysis of reducing the heat load's ways and means, the design method for multi-metal hot forging dies is proposed.

分析了降低熱負荷的方法和途徑，提出多金屬熱鍛模設計方法。

This paper presents the development of a new type build-up welding rod used for hot forging die.

研究了一種新型熱鍛模堆焊焊條。

During the process of hot forging, the temperature has a great effect on the mechanical performance of the material.

溫度對熱鍛模的力學性能有很大影響，溫度的變化導致鍛模失效。

Improper material composition and processing can cause earlier fracture failure and short life happened to the hot-forging dies.

不恰當的材質及工藝導致熱鍛模具出現早期斷裂失效，失效形式不合理，壽命較低。

the thermal stress is the most fundamental failure reasons on the base of the distribution of stress field in hot forging dies.

根據應力場得出熱應力是熱鍛模失效的最根本的原因。

The steels can obtain better strength and toughness by subsequent air cooling after hot forging or rolling without any heat treatment.

本鋼種無需經過任何熱處理，經鍛軋后空冷就能達到較好的強韌性。

I think a radiator thermostatic valve used on the body is simple, using hot forging is very appropriate.

我認為在暖氣上所使用的溫控閥屬于簡單閥體，采用熱鍛是非常合適的。

The lifetime of hot forging die decreases greatly owing to softened layers brought by high thermal loadings.

熱鍛模壽命由于高的熱載荷引起其表面層軟化而大大下降。

The importance of numerical simulation of microstructure evolution during metal hot forging was introduced in this paper.

闡述了金屬材料塑性加工中微觀組織演變數值模擬的重要性。

And it's difficult to process. The traditional hot forging process needs big energy and has Large amount of follow-up Machining.

傳統的熱模鍛工藝能耗大，后續機加工量大，生產成本高、缺乏市場競爭力。

The hot-forging dies made by new-type precision casting die steel are applied on site.

采用新型精鑄模具鋼制備熱鍛模并進行現場應用。

The problems in cast technologies of hot-forging dies are pointed out and suggestions are presented.

指出了精鑄熱鍛模具制造中存在的成型問題，并提出了建議。

A precise spray forming device for hot forging dies was designed and fabricated based on spray forming principles.

基于噴射成形基本原理設計了熱鍛模精密噴射成形裝置，闡述了其關鍵技術及模具成形特點。

The application status of precision cast hot-forging dies in the world are summarized.

簡述了精鑄熱鍛模具國內外應用狀況，對鑄造模具鋼的研究進展進行了研究。

Hot forging, rolling, extrusion, etc.

熱鍛、滾軋、熱壓等等。

Simulation Analysis for Effects of the Parameters on the Surface Temperature of a Hot Forging Die

工藝參數對熱鍛模表層溫度的影響模擬分析

Development of Build-up Welding Rod Used for Wear-Resistance and Cold-Heat Fatigue Resistance Hot Forging Die

熱鍛模耐磨耐冷熱疲勞堆焊焊條的研制

Heat Treatment Technology for Increasing Service Life of Hot Forging Die of Bearing Rings

提高套圈熱鍛模使用壽命的熱處理工藝

Application and Improvement of Service Life of Hot-forging Dies Prepared by Cast Steel

精鑄模具鋼熱鍛模的應用及壽命的提高

Rigid-Plastic Finite Element Method Analysis of the Thermodynamic Couple in Hot Forging Forming Process

熱鍛中的變形-傳熱耦合剛塑性有限元模型的建立

Standard Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging

后熱鍛用微合金，高質量，熱鍛鋼棒的標準規范

The Technological Parameter Optimization of Gear Billet Hot Forging Process with Damage Minimization

基于最小損傷值的齒輪毛坯鍛造成形過程工藝參數優化設計

Specification for Steel Bars, Microalloy, Hot-Wrought, Special Quality, for Subsequent Hot Forging

特殊質量微量合金熱鍛鋼棒規范.后續熱鍛件規范

Reverse Copying and Amendment of Tool Electrode for the Electrochemical Machining of Hot Forging Die

熱鍛模電解加工工具電極的反拷和修正

Numerical simulation and microstructure prediction for hot forging process

熱鍛工藝數值模擬及微觀組織預測技術

Numerical simulation of microstructure evolution of flange axle during hot forging

法蘭軸熱鍛過程中的微觀組織演變的數值模擬

Microstructure simulation in hot die steel after hot forging and simulation software design

熱作模具鋼鍛后組織模擬及軟件設計

Review of numerical simulation for the cooling process of the structural steel hot forging

結構鋼熱塑性變形后冷卻過程的數值模擬研究綜述

The Invalidation Analysis and Strengthen Treatment of Hot Forging Die for Automobile Gears

汽車齒輪胎熱鍛模失效分析及強化處理

Methods Improving Service Life of Hot Forging Die

提高熱鍛模具使用壽命的方法

Cast Technologies and Its Application in Hot-forging Dies

精鑄熱鍛模具的成型方法及應用

Failure Analysis on Anomalous Split of Combination Hot-forging Dies for Engine Valves

組合式氣門鍛模非正常開裂失效分析

Research of quality control and process optimization of gear billet hot forging

齒輪毛坯鍛造成形內部質量控制與工藝優化設計

Improvement of Heat Treatment Process of the Hot Forging Dies for Connecting Rod

連桿熱鍛模的熱處理工藝改進

Selection of Tempering Technology of New Cast Die Steel for Hot Forging

新型鑄造熱鍛模鋼回火工藝的選擇

Numerical Simulation of crankshaft in hot forging procedure

曲軸鍛造過程的數值模擬

The Hot Forging-Cold Forging Combined Plastic Forming Technology

熱鍛-冷鍛復合塑性成形技術

Numerical simulation of Fore closure in solid cylinder under hot forging

圓柱體內部空洞熱鍛閉合過程的數值模擬

Alloying Design and High-temperature Wear Property of Cast Hot-forging Die Steel

精鑄熱鍛模具鋼的合金成分設計及其高溫磨損性能研究