brinell

brinell

美 　英

• 網絡布氏；勃氏；勃氏硬度

例句

The function and mathematics model between brinell hardness and annealing temperature was established.

建立布氏硬度和退火溫度之間的函數及數學模型。

Brinell or Vickers or Rockwell hardness is normally determined for product forms C and H in heat treatment condition A.

對于C型和H型鋼，通常在熱處理條件A下確定其布氏、維氏或洛氏硬度。

Metallic materials. Brinell hardness test. Part 2 : verification and calibration of testing machines.

金屬材料.布氏硬度試驗.第2部分：試驗機的驗證和校正

The impeller, wear plate and agitator are made of abrasive resistant 28% chrome iron (600 Brinell, 57 Rockwell C).

設備中的葉輪，耐磨板和攪拌器全部采用耐磨的28%的鉻鐵制作。

Metallic materials. Brinell hardness test. Part 3 : calibration of reference blocks.

金屬材料.布氏硬度試驗.第3部分：標準試塊的校正

At room temperature Brinell hardness (HB) of extruded alloys were over 80.

擠壓變形合金的室溫布氏硬度（HB）都超過了80。

Static test methods including Brinell, Rockwell, Vickers, Knoop, Wechsler, such as Pap.

靜態試驗方法包括布氏、洛氏、維氏、努氏、韋氏、巴氏等。

Calibration of standardized blocks to be used for Brinell hardness

標準布氏硬度塊的標定

Research of the Correspondence Theorem Apply to Brinell-hardness and Diamond Penetrator-hardness Testing

探討相似定律在布氏和維氏硬度試驗中的應用

test values can be converted to magnitude, Brinell, Rockwell, Vickers hardness;

可將測試值轉化為里氏、布氏、洛氏、維氏硬度值；

Metallic materials - Brinell hardness test - Calibration of reference blocks

金屬材料.布氏硬度試驗.標準塊材的校準

Metallic materials - Brinell hardness test - Verification and calibration of Brinell hardness testing machines

金屬材料.布氏硬度試驗.布氏硬度試驗機的鑒定和校準

Brinell Hardness Number Blank , Block Bottom Bearing Break Bracket Broach Brass Bronze Basic

底部軸承破裂支架鉆孔黃銅青銅棕色&形狀基本的套管

Metallic materials - Brinell hardness test - Part 3: Calibration of reference blocks; example of design of reference blocks

金屬材料.布氏硬度試驗.第3部分：標準試塊校驗.標準試塊設計樣品

Metallic materials - Brinell hardness test - Test method

金屬材料.布氏硬度試驗.試驗方法

Brinell hardness number Battery Limit Battery Line Bill of Loading Blind Black Blank

盲板黑色空白基準標志彎矩界區界區線載荷數據表

Introduction of 2002 Edition National Standard of Metallic Materials-Brinell Hardness Test

介紹2002版金屬布氏硬度試驗國家標準

Standard Test Method for Brinell Hardness of Metallic Materials

金屬材料布氏硬度的標準試驗方法

Verification of Brinell hardness testers

布氏硬度計的檢驗

Test methods for bare wires--Hardness test--Brinell hardness test

裸電線試驗方法硬度試驗布氏法

metallic materials - test method of brinell hardness

金屬材料-布氏硬度測試方法

standardized blocks of brinell hardness

布氏硬度標準扁

Analysis and elimination of errors in Brinell-hardness test

布氏硬度試驗誤差分析及排除

hammering type Brinell hardness tester

錘擊式布氏硬度計

Under normal circumstances, sealed with 45 sets of quenched and tempered steel processing, Brinell hardness of 240 or above;

一般情況下，密封套采用45鋼調質處理，布氏硬度達到240以上；

Metallic materials - Brinell hardness test - Part 1: Test method

金屬材料.布氏硬度試驗.第1部分：試驗方法

radial arm Brinell hardness tester

搖臂布氏硬度試驗機