ovality

美 [o?'væl?t?] 　英 [??'væl?t?]

• n.〔工〕橢圓度
• 網絡卵形度；不圓度；最大橢圓度

英漢解釋

n.	1. 〔工〕橢圓度,卵形度

例句

Acceptable ovality for refractory performance is derived empirically from many years of observation.

對耐火磚襯可接受的橢圓度只可來通過多年觀察得來經驗取得。

The bended part of a tube has the ovality less than 2%, smooth inside wall without folding and even outside wall thickness without crack.

彎管部位管材的橢圓度小于2%，內壁光滑無皺褶，外部壁厚均勻無開裂。

The errors of the stand-off measurement and measurement errors made by pitch diameter gauge and ovality gauge are analyzed and compared.

分析比較了緊密距測量以及中徑和橢圓度量規測量的誤差。

Casing, cement and formation plane strain mechanical model are established, considering casing with initial ovality .

針對套管的不同初始橢圓度建立了套管、水泥環、地層平面應變力學模型。

Ovalisation meters measuring ovality during the test were used in the full scale testing, however.

在該測試中用于測量橢圓度的成橢圓形儀表也可用于大型的測試，但是。

Lacking internal support in the pipe, this pipe bending process creates some cross section ovality.

在管道內支持不足，這根管子彎過程中創造一些截面橢圓。

Preparing the ovality analysis: measuring the temperature of kiln shell and tyre, resp.

橢圓度測量的準備工作：測量相應的窯筒體和輪帶溫度。

The cross-section distortion of bent tube is very small by using ball filler push bending process, with the ovality less than 1. 5%.

運用珠粒填料推彎成形工藝成形出的管材截面畸變程度很小，橢圓度不超過1.

After rolling, welding and heat-treatment, the pipe may have some defaults, such as out-of- straightness and ovality .

經過軋制、焊接和熱處理后，鋼管存在軸線方向彎曲和橫截面橢圓度的缺陷。

Feasibility Analysis of Substituting Pitch Diameter Gauge and Ovality Gauge for Thread Work Gauge

用中徑和橢圓度量規替代螺紋工作量規的可行性分析

Diameter Tolerance, Ovality and Average Decarburized Layer Depth

直徑公差，偏圓度及脫碳層的平均深度

FE Analysis of Influence by Oil Casing Ovality on Its Extrusion Strength

用有限元法分析石油套管的橢圓度對承載能力的影響

The magnetic principle and method of on-line testing of ovality of coiled tubing

連續油管橢圓度在線磁性檢測原理與方法

Measuring Ovality with the Ovality Tester

使用橢圓度測量儀測量橢圓度

Tolerance of Wire Diameters & Ovality

圓徑及偏圓度之公差

Analysis of Ovality of Cylinder Barrel Tube

油缸筒用鋼管橢圓度分析

Fixing of Ovality Tester on shell

在窯筒體上固定橢圓度測量儀

Why need pay such attention to Ovality

為何要關注橢圓度