piercer

piercer

美 　英 ['p??s?]

• n.穿孔的人[物]；鉆孔器；(酒桶等的)開口器；(昆蟲的)產卵管
• 網絡穿孔機；沖孔器；穿孔心棒

英漢解釋

n.	1. 穿孔的人[物];鉆孔器,錐;(酒桶等的)開口器 2. (昆蟲的)產卵管,螫針 3. 〈俚〉銳眼

例句

Production experiences gained from putting into production of the piercer matched with a three roll mill are summed up.

總結了該機匹配三輥軋管機組投產以來的生產經驗。

The piercing principle of 2-roll cross-rolling piercer and its application range are discussed.

論述了二輥斜軋錐形輥穿孔機的穿孔原理及其應用范圍。

The control group: the road of pedicle screw was ready with using an ordinary piercer.

對照組按傳統手術操作方法，使用普通的椎弓根螺錐準備釘道；

The paper researched and put forward the test system project about ? 350 piercer's rolling pressure and rolling moment .

論文研究提出了？350穿孔機的軋制壓力和軋制扭矩的測試系統方案。

The paper offered relatively formula for piercer's designing and fabrication in the future.

為今后設計、制造二輥斜軋穿孔機提供了比較簡明合理的參考計算方法。

It can be used not only for pass design and off line analysis but also for guiding in the adjustment of piercer.

該系統不僅可用于斜軋穿孔工具設計和離線分析，還可用于指導穿孔機操作。

Failure Type Analysis and Studies on Prolonging Service Life of Piercer Plug for Seamless Steel Tube

無縫鋼管穿孔頂頭失效形式分析及提高使用壽命的研究進展

Description of Piercer Mill and the Research of the Premium Arrangement of Driving Spindles for the Cone Type Piercer Mill

錐形輥穿孔機綜述及其軋輥傳動軸布置方式初探

Discussion on the Piercing Principle of Cone Roll Piercer and Its Application

關于錐形輥穿孔機的穿孔原理及應用問題的討論

Comparison of Two Roll Cone Shaped Roll Piercer with Three Roll Barrel Type Piercer

二輥錐形輥穿孔與三輥鼓形輥穿孔對比分析

Optimization design on intelligent propulsion system of Wave-piercer Catamaran with hydrojet propulsion

噴水推進的穿浪艇智能推進系統初步優化研究

Improving Piercer Feed Angle to Enhance Piercing Effeciency

改進穿孔機送進角提高穿孔效率

New Technology of Rolling Block to Avoid in Three-roll Piercer

三輥軋管過程避免軋卡的新工藝

Design and Reform of the Roll Box of Mannesmann Piercer

曼氏穿孔機軋輥箱改造設計

Approach on Characteristics of Cone-type Piercer

國產錐形穿孔機的特點分析

Automatic piercer of bearing retainer

軸承保持架自動沖孔機

Automatic Position Control System of Piercer

穿孔機的自動位置控制系統

DESIGN OF PIERCER FOR BATTERY TROUGH

蓄電池槽打孔機設計

The Three-dimensional Parameterized Design of Piercer Guide Board Series

穿孔機導板系列的三維參數化設計