cylindricity

cylindricity

美 [s?l?nd'r?s?t?] 　英 [s?l?nd'r?s?t?]

• n.圓筒度
• 網絡圓柱度；園柱度；柱面度

英漢解釋

n.

1. 圓筒度

例句

The cylindricity error can be got by optimization. The results show that this method can get cylindricity error without damage and touch.

實驗結果表明，該方法可以在無接觸無破壞的前提下得到較為準確的測量結果。

Then the edge points of the pipe are extracted by Facet model. The cylindricity error can be obtained by the least square cylinder.

在已知所有邊緣點信息的基礎上采用最小二乘圓柱法求得管道的圓柱度誤差。

The cylindricity error separation and reconstruction method proposed in this paper was systematically verified.

利用自律驗證法對本文提出的圓柱度誤差分離及重構方法系統地進行了實驗驗證。

Cylindricity error is defined as the changes between measured column and ideal column.

圓柱度誤差是指實際被測圓柱面對其理想圓柱的變動量。

Based on industrial CT, this dissertation studied the cylindricity error evaluation and inner surface display of pipeline.

本文以工業CT為基礎，研究了工件內部管道的圓柱度測量與內表面顯示算法。

The experimental results show that the roundness is improved by 40% and cylindricity by 23% after compensation.

實驗結果表明，補償后的工件圓度誤差平均改善了40%，圓柱度誤差平均改善了23%。

Because of the limit of measuring tools, the traditional methods can not evaluate the cylindricity error of internal pipe.

由于測量工具的限制，傳統方法對無法充分接觸的內部管道的圓柱度難以測量。

While the plane is measured by using the cylindricity measuring instrument and square, the data acquisition should be done at the same time.

首先利用圓柱度儀和角尺對被測件進行測量，同時采集原始測量數據，然后利用最小二乘法實現平面度誤差的評定。

Study on Measurement of Cylinder's Taper and Run-out on Cylindricity Measuring Instrument

圓柱度儀測量圓柱體錐度及跳動的研究

Establishment and Solution of Mathematical Evaluating Model for Linear Programming of Cylindricity Error

圓柱度誤差評定線性規劃模型的建立與求解

Method for Cylindricity Errors Evaluation Using Particle Swarm Optimization Algorithm

基于粒子群算法的圓柱度誤差評定方法

The New Arithmetic of Cylindricity Error and Its Application in Micro computers

圓柱度誤差新算法及其在微機上的實現

Optimization of Cylinder Bore Honing Platform Structure and Improvement of Cylindricity

缸孔平臺結構的優化及圓柱度的改善

Analysis of the Cylindricity Tolerance and Press Mounting Curves of Axle Wheel Seat and Wheel Hub Bore

關于車軸輪座、車輪輪轂孔的圓柱度公差和壓裝曲線分析

A Practical Algorithm for Computing Cylindricity Error in the Rectangular Coordinates

直角坐標系下計算圓柱度誤差的一種實用算法

Research on Virtual Cylindricity Error Measuring Instrument

虛擬圓柱度誤差測量儀的研究

Cylindricity Error Evaluation Based on an Improved Genetic Algorithm

基于改進遺傳算法評定圓柱度誤差

Measurement techniques of cylindricity with three-point method

圓柱度的三點法測量技術

Error Separated Method of Measuring Datum for Cylindricity Measurement

一種圓柱度測量基準的誤差分離方法

Application of DNA Computing Model to Cylindricity Error Evaluation

DNA計算模型在圓柱度誤差評定中的應用

Application of laser measuring method on detection of cylindricity error

激光測量法在圓柱度誤差檢測中的應用

The measuring cylindricity error with precision and non-touching method

圓柱度誤差的非接觸精密測量方法

The Minimum Area Principle of Computing Methd's Research for Data Processing of Roundness Cylindricity and Coaxality

圓度、圓柱度和同軸度計算機測量數據最小區域法處理算法研究

Optimization Evaluation of Cylindricity Error Based on Correctional Simplex Method

基于修正單純形法的圓柱度誤差優化評定

Analysis of several cylindricity measurement models based on error separation technique

基于誤差分離技術的幾種圓柱度測量模型分析

Data Processing in Testing Cylindricity Error

圓柱度誤差檢測中的數據處理

Accurate Assessment of Departure from Roundness and Cylindricity Based on the Optimal Control

基于最優控制的圓度圓柱度誤差精確評定

Method of error separation based on photoelectric Sensor in measurement of cylindricity

圓柱度測量中基于光電傳感器的誤差分離方法

On-Line Cylindricity Measurement Based on Wavelet Harmonic Analysis

一種基于小波多頻分析的圓柱度在線檢測方法

Calculating method of cylindricity error based on immune algorithm

基于免疫算法的圓柱度誤差的測量

A Novel Method and Technology for Cylindricity Errors Separation

一種新的圓柱度誤差分離方法和技術