work-hardening

work-hardening

美 　英

• un.冷加工硬化
• 網絡功硬化；變形硬化；負偏離

詞形變化

過去分詞：work-hardened  現在分詞：work-hardening  第三人稱單數：work-hardens  

英漢解釋

v.	1. to increase the hardness or strength of a metal by subjecting it to compression, tension, or another mechanical process

例句

Furthermore, the work hardening capacity, bake-hardening properties and anti-hollow capacity of high strength steel are researched as well.

對高強度鋼板的強化機制進行分析，根據其強化機理可以更好的預測其成形性能并指導實際生產；

Due to work hardening in the groove area, ductile materials and tempers should be specified.

由于需要對凹槽進行硬化，所以需要指定塑性材料和回火。

The cold work hardening is affected by both the recovery and recrystallization after cold work and by the solid solution temperature.

合金冷作硬化效果與合金的回復和再結晶程度及固溶處理溫度有關。

Work-hardening near the blind hole is caused by hole chilling when residual stresses are measured by the blind hole method.

盲孔法測量殘余應力時，鉆孔會在盲孔附近產生加工硬化。

When work-hardening exponent of tube material get bigger, the formability of the tube is better.

管坯材料的加工硬化指數越大，材料的成形性能越好。

The results show that the work hardening rate of pure tantalum is low.

研究結果表明：純鉭的宏觀加工硬化速率比較低。

The stress increased slowly with strain increased when strain was above 5%, and work hardening rate decreased.

當應變量大于5%時，應力隨著應變的增加而緩慢增加，加工硬化速率降低。

heated. or welded without such complications as work hardening.

加熱。或者焊接，這種方法沒有加工硬化的問題。

or welded without such complications as work hardening.

沒有這樣的并發癥或焊接工作硬化。

what is the effect of work hardening phenomenon on metallic material?

金屬材料的加工硬化現象對金屬材料的力學性能有何影響？。

Effect of cold work hardening on stress corrosion cracking of stainless steels in primary water of pressurized water reactors

冷加工硬化對壓水堆一回路水中不銹鋼應力腐蝕裂紋的影響

Effect of Nitrogen, Carbon and Manganese on Work-Hardening Ability of Metastable Austenite Manganese Steel

氮碳錳對介穩奧氏體錳鋼加工硬化性能的影響

work hardening precipitation hardening strain aging quench aging sensitizention

加工硬化沉淀硬化應變實效淬火實效敏化

The influence of machining processes of fastening holes on surface work hardening

緊固孔的加工工藝對其表面硬化的影響

Experiment and Study on Cold Work Hardening to Increase the Permanence Limit of Mechanism

表面硬化處理對提高構件持久極限的試驗研究

Stress distribution near tip of shallow notch for power-work-hardening material

冪硬化材料淺切口根部附近的應力分布

On the effects of specimen recycling to the tensile strength and work hardening

試樣復用對拉伸強度和被粘物加工硬化的影響

Research on the Ability of Work Hardening of High Manganese Steel at the Condition of Simulating Actual Work

模擬實際工況條件下高錳鋼加工硬化能力的研究

Work hardening rate and microstructure of tantalum

鉭的加工硬化速率及其顯微組織

The Research on Surface Work - hardening in High Speed Lapping

高速研磨表面加工硬化的研究

Work Hardening Ability of As-cast Manganese Steel

鑄態錳鋼的加工硬化性能

Simulation of Surface Work-Hardening Caused by Metal Cutting

金屬切削中工件表層加工硬化模擬