electrometer
美 
英
- n.量電表
- 網絡靜電計；靜電表；電位計
詞形變化
復數：electrometers
英漢解釋
英英解釋
例句
The measured current is usually quite small, so a picoammeter or electrometer is often required to make the measurement.
測得的電流通常非常小，因此往往需要使用皮安計或靜電計進行測量。
To measure the offset of a switch card, connect the output of the card to a pico ammeter or electrometer.
若要測量開關卡的偏移電流，請將卡的輸出連接到一臺皮安計或靜電計。
Figure 2-39 shows an electrometer connected to a current source that consists of a voltage source in series with a resistor.
圖2-39所示為靜電計和由電壓源及電阻器串聯組成的電流源相連接。
Refer to the electrometer's manual or specifications for the value of the feedback impedance for a particular instrument.
特定儀器反饋阻抗的數值請參見該靜電計的手冊或技術指標。
When a charged object is placed within the inside electrode, an induced charge will flow into the electrometer.
當帶電物體放到內電極里面的時候，就有感生電荷流過靜電計。
Quartz has properties similar to sapphire, but considerably higher piezoelectric output, so it's rarely used in electrometer circuits.
石英具有類似于藍寶石的性質，但是其壓電輸出相當高，所以很少用于靜電計電路中。
Connect the HI terminal of the electrometer to one end of the resistor and the HI of the voltage source to the other end.
將靜電計的HI端連到電阻器的一端，將電壓源的HI端連到電阻器的另一端。
These low current measurements are often made with an electrometer or source-measure unit.
這些弱電流測量工作常常使用靜電計或源-測量單元來進行。
The resistors (RL) are current limiting resistors used to protect the switches and electrometer from high current.
電阻器（RL）是電流限制電阻器，用來保護開關和靜電計不受大電流的損害。
Since the voltage burden of the electrometer ammeter or picoammeter is less than 1mV, the diodes won't conduct.
由于靜電計、安培計或皮安計的輸入端壓降小于1mV，這兩個二極管不會導通。
The external feedback mode allows an external device to be used as the feedback element of the electrometer.
外部反饋模式允許使用外部器件來作靜電計的反饋元件。
As shown in Figure 2 - 40, this will cause a current (i) to flow through the low to ground capacitance of the electrometer (IM).
如圖2-40所示，這將會引起電流（i）流過靜電計（IM）的低端到地的電容。
Two general types of connectors are used for electrometer, picoammeter, and SMU measurements.
靜電計、皮安計和SMU的測量工作中使用兩種通用類型的連接器。
The electrometer ohmmeter makes a two-wire resistance measurement at a specific test current, depending on the measurement range.
靜電計歐姆計依據測量的量程，在規定的電流下，進行兩線電阻測量。
General Electrometer Considerations: A discussion of techniques and error sources that affect high impedance measurements in general.
一般靜電計要考慮的問題：一般性地討論影響高阻測量的技術和誤差來源。
The following paragraphs examine considerations that apply to all types of electrometer and SMU measurements on high resistance sources.
以下各段考察所有類型的靜電計和SMU在測量高阻源時要考慮的問題。
This can be done by placing the object in a Faraday cup and measuring the charge with an electrometer .
可以把物體放在法拉第杯中，用靜電計測量其電荷。
The damping circuit may already be built into the electrometer or may be an external circuit.
衰減電路可以裝在靜電計的內部，也可以是一個外部電路。
The circuit of the electrometer when used as a voltmeter is actually as shown in Figure 2-6.
當靜電計作為電壓表使用時，其電路實際上如圖2-6所示。
The Model 6517A Electrometer has the Alternating Polarity Method built into a test sequence.
6517A型靜電計與變換極性法已被做成一個現成的測試程序。
It can be readily measured, however, with an electrometer by using the technique described in Section VI-B.
它可以用靜電計輕而易舉地測定，其使用方法如第六節B所述。
To avoid measurement errors, it's critical to make proper connections from the electrometer, SMU, or picoammeter to the device under test.
為了避免測量誤差，關鍵之點在于將靜電計、SMU或皮安計和被測裝置進行適當的連接。
Refer to the instrument's instruction manual for information on a particular electrometer 's internal damping feature.
關于特定靜電計內部衰減電路的性能，請參閱該儀器的操作手冊。
The basic configuration of the constant-voltage method using an electrometer or picoammeter is shown in Figure 2-30a.
使用靜電計和皮安計的恒壓法的基本電路配置如圖2-30a所示。
The inside electrode is connected to the electrometer HI and the outside electrode is connected to the electrometer LO.
內電極連到靜電計的HI端，外電極連到靜電計的LO端。
Picoammeters and SMUs also have very low input bias currents, although usually not as low as an electrometer 's.
皮安計和SMU也具有很低的輸入偏置電流，但是通常沒有靜電計低。
The forward-biased diode in series with the HI electrometer (pA) terminal also serves to limit the AC gain.
與靜電計（pA）的HI端子串聯的正偏二極管也起到限制交流增益的作用。
This application employs a Model 6517A Electrometer, which can supply the test voltage and measure the residual voltage.
這種應用情況使用了一臺6517A型靜電計，它能夠供給測試電壓并測量剩余電壓。
Figure 2-24 shows a protection circuit for an electrometer ammeter or picoammeter, consisting of a resistor and two diodes (1N3595).
圖2-24示出靜電計或皮安計的過載保護電路，其中包括一個電阻器和兩個二極管（1N3595）。
Given that the offset current may be hundreds of picoamps or less, an electrometer or picoammeter is required to measure it.
給出的偏移電流技術指標可能為幾百皮安或更小，需要利用靜電計或皮安計進行測量。
Main Control Unit, two-channel electrometer and servo controller.
主控制器單元，帶有兩通道靜電計和伺服控制器。
The ohmmeter uses an internal current source and electrometer voltmeter to make the measurement.
歐姆計使用內部的電流源和靜電計電壓表來進行測量。
An electrometer makes an ideal coulombmeter because it has very low input offset current and high input resistance.
靜電計是一個理想的庫侖計，因為它具有非常低的輸入偏置電流和很高的輸入電阻。
Because of the high input resistance and low offset current, the electrometer voltmeter has minimal effect on the circuit being measured.
由于具有高輸入電阻和低偏置電流，靜電計電壓表對被測電路的影響極小。
It can be readily measured, however, with an electrometer by using the technique described in Section VI-B.
它可以用靜電計輕而易舉地測定，其使用方法如第六節B所述。
Therefore, a voltmeter with high input resistance, such as an electrometer, is required.
所以需要使用具有高輸入電阻的電壓表，例如靜電計。
Electrometer ammeters and picoammeters and methods of making low current measurements were described in Sections 1 and 2 respectively.
第一章和第二章已經分別對靜電計和皮安表以及弱電流測量的方法等問題進行了介紹。
Figure 2-42 illustrates a clipped waveform taken from the 2V analog output of an electrometer.
圖2-42示出在靜電計的2V模擬輸出端觀察到的限幅波形。
Figure 2-33 shows the electrometer ohmmeter measuring a resistance (R).
圖2-33示出靜電計歐姆計測量電阻（R）的情況。
See Section 2. 6. 6 for details on appropriate cabling and connector types for electrometer measurements.
有關靜電計測量時恰當的電纜和連接器類型的詳細情況，請見第2.6.6節。
The Model 7001 Switch System switches the electrometer and voltage source to each test pattern, X1 through X10.
7001型開關系統將靜電計和電壓源切換到每個對象，X1到X10。
