trunnion
美 ['tr?nj?n] 
英 ['tr?nj?n]
- n.【機】耳軸；空樞；炮耳
- 網絡軸頸；樞軸；耳軸樞軸
詞形變化
復數：trunnions
英漢解釋
英英解釋
例句
WILLIAMSONs metal to metal sealed trunnion ball valve is in general of the front ball sealing structure.
威廉姆森金屬硬密封固定球閥一般采用球前閥座密封結構。
The trunnion assembly is supported by air bearings at the end of each arm and is held in position by brake shoes at each bearings.
耳軸組件的支承是每根臂末端的空氣軸承，軸承上的閘瓦起定位作用。
In general, WILLIAMSONs trunnion ball valve features the front ball sealing design structure.
威廉姆森固定球閥一般采用球前閥座密封結構。
The load and air cylinder can swing round the pin in a plan, if the stroke is long, adopt the intermediate fixed or movable trunnion type.
負載和氣缸可繞鉸軸在一個平面內擺動，氣缸長行程時，建議采用中間鉸軸式
Trunnion design allows multi-directional flow; means that the valve is in no danger of being installed "backwards. "
耳軸設計允許多向流動，使閥門在“逆運轉”時沒有危險。
The showering trunnion mounting water cock, the choice is shorter, does not use the too long water pipe showering.
淋浴器安裝節水龍頭，選擇較短，不用太長水管的淋浴器。
Special Trunnion sizes and configurations are available. Consult factory when ordering.
可提供特殊的軸徑尺寸和配置，請在訂購時咨詢工廠。
and an adaptive curved cushion group is arranged between the trunnion ring retainer seats(3) and the converter shell seat(4).
所述托圈擋座（3）與所述爐殼座（4）之間還設置有自適應曲面墊組。
Handling and transport design of converter trunnion for Panzhihua ISC .
攀鋼轉爐耳軸的裝運設計。
Trunnion Design: Upper and lower supports retain ball under pressure.
耳軸設計：在壓力下上下支持閥球。
Application : Slag line of ladle , trunnion of converter and the line of EAF .
用途：用于鋼包渣線、轉爐耳軸及電爐的噴補。
The discharge trunnion liner, finally it finally fell to the ground and broke his leg.
蹌，最后它終于跌倒在地，折斷了腿。
screw yoke apart from the transmission output shaft and remove the trunnion cross.
從轉換器輸出軸移動螺桿套分離并拆下耳軸。
journal of the shock strut in the aft trunnion bearing(Fig. 408).
安裝減震支柱后軸頸支耳到后軸頸軸承中（圖408）。
The QTCV-T1 trunnion-mounted rotary control valve designed for general control valve service.
T1型裝有底軸的旋轉控制器是用來為普通控制閥服務的。
so that the shock strut will not touch it(Stage2, Fig. 405). Attach the trunnion link in position to clear the gear.
移開軸頸連桿，以避免減震支柱與之接觸（圖405，第2步），將軸頸連桿固定在一遠離起落架的位置上。
The trunnion journal (22) is made by cutting hardened steel with using no cutting fluid.
該耳軸軸頸（22）通過淬火鋼的干式切削形成。
support shaft(5) through the reaction link universal(3) and the trunnion link pin(6) from the aft side.
從后側面，通過反應連桿萬向接頭（3）和軸頸連桿銷（6）安裝彈簧支撐軸（5）。
Refined Calculation on Tilting Moment for AOD Converter and Presentation of the Safety Position of the Trunnion
AOD爐傾動力矩精確計算及耳軸中心安全高度位置確定
Performance, reliability, and provision of the horizontal trunnion type
性能、可靠性和提供水平的軸徑類型
Fitting up and welding technology of steelmaking converter trunnion ring
煉鋼托圈的組對及焊接工藝
Dynamic load capacities for horizontal and trunnion type centrifugal casting machines are:
臥式和耳軸型離心鑄造機的動態負載能力為：
Shipbuilding and marine structures; Trunnion pieces for span bearings and lead block bearings
造船和海上建筑物.跨架軸承和導向滑塊軸承的樞軸配件
Processing Plan to Ensure Trunnion Co-axiality During Assembly Welding of Converter Trunnion Ring at Site
轉爐托圈現場組焊保證耳軸同軸度工藝方案
Profile Modeling for Longitudinal Forward Kinematic Track of Push-arm Trunnion of Bulldozer
推土機履帶臺車架鉸點縱前向運動軌跡的仿形
Trunnion mounts handle high differential pressures and prevent side loading
安裝軸頸處理高壓差并防止側面負載
Design of Hydraulic Hoists for Eccentric Trunnion Sector Gates of Xiaolangdi Project
小浪底水利樞紐偏心鉸弧形閘門液壓啟閉機設計
Repair and improvement to the trunnion on a cutter suction dredger
絞吸式挖泥船橋梁耳軸修復和改進
The Improvement of Turbine Guide Vane Trunnion Seal for Sanmenxia Water Power Plant
三門峽電站水輪機導葉軸頸密封改造
Measurement and Analyses for Trunnion Pin's Disalignment of Converter
轉爐托圈耳軸同軸度的測定及其理論分析
Dynamic Analysis of Middle Axis of Double Ring- and- trunnion Universal Joint
十字環槽式雙萬向聯軸器中間軸動力學分析
Improvement in technology of Large steel water pitcher trunnion
大型鋼水罐耳軸的鍛造工藝改進
Finite Element Analysis of Double Ring-and-trunnion Universal Joint
十字環槽式雙萬向聯軸器有限元分析
Technology Development of Lower Trunnion Centre Drive and Its Application for Ljungstrom Air Preheater
空氣預熱器下軸中心變頻驅動技術
FORWARD TRUNNION BEARING FUSE FASTENER;
前耳軸軸承保險緊固件；
Study and application of VSR technique on trunnion steel girder
支鉸鋼梁振動時效技術研究與應用
The study of riding comfort model of triple-axles truck with trunnion suspension
三軸平衡懸架載貨汽車平順性建模研究
Cracks Emergency Treatment on Trunnion and Mill shell
水泥磨中空軸及筒體裂紋的應急處理
Reparative try ofseriously damaged ball mill trunnion in Shaoguan Power Plant
韶關發電廠磨煤機軸頸嚴重損傷后的修復新嘗試
Repair Welding of Converter Trunnion at Driven Side
轉爐驅動端耳軸的補焊
