burrs

burrs

美 [b?r] 　英 [b??(r)]

• n.伯爾；粗磨(刀)石；(銅版等的)粗刻紋；【機】毛口
• v.用粗喉音說(話)；用粗喉音說話
• 網絡毛邊；毛刺；工件之毛邊

詞形變化

同義詞

英漢解釋

英英解釋

例句

The places Passengers can reach are not allowed to have exposed sharp edges, burrs, monoceras and dangerous material, convex knife.

乘客可觸及之處檢查不允許有外露的銳邊、毛刺、尖角和危險凸刀出物。

If a cover design-time to set aside the bottom side of the head, burrs, and sizes, this behavior completely avoidable.

如果在封面設計時留出天頭、地腳的毛邊尺寸，這種現象完全可以避免的。

Check the surface of pipes to avoid burrs and sharp angle, which could spare all damages to wires in the process of installation.

檢查管道外表面確認無毛刺、銳角，以免在安裝時對電纜造成損壞。

Coating the outer wall are protein fragments that resemble burrs, the hooks that bristle around the outside of certain seeds.

覆蓋外壁的是像毛刺的蛋白質，鉤子直立在某些種子的外部。

Thread-bound book cover general paper is to use the same color as the book block of burrs, paper, or green-blue coloring sheet.

線裝書封面用紙一般是使用與書芯顏色相同的毛邊紙，或用青藍色的染色紙。

Finally select the subtraction, material Park, select simple layout, and to the refined burrs, and this form of binding.

最后還是選擇減法，用材質樸，選擇簡潔的版式，并以改進后的毛邊本形態裝訂。

Provided with a burr-trimming cutter, the bias-adjustable device can remove automatically the burrs on the polished rod.

調偏裝置設計有光桿修復刀，可自動修除光桿上的毛刺。

Only a single side of burrs, and paper making and membership card production, mainly for the ancient books available.

毛邊紙只宜單面制卡和會員卡制作，主要供古裝書籍用。

The stacks must be free of oil and blanks to have burrs oriented in the same direction.

這些堆疊的必須是無油和毛坯有毛刺面向在同一方向。

Tungsten-carbide rotary burrs like a milling cutter with handle, is used in that complex inside of mould machining finish machining work.

硬質合金旋轉銼類似帶柄小銑刀，用于各種模具復雜型腔的精加工。

Burrs, slivers, scabs and weld spatter visible following blasting shall be removed and the area re-blasted.

噴砂之后，應當除掉明顯的毛刺、裂片、瑕疵和焊渣并對此處再次噴砂。

drilling and fine blanking as well as the burrs formed on curved surfaces.

鉆井和精沖以及彎曲表面形成的毛刺。

Turbulence - burrs left on the cut tubing causes a tumbling effect causing localized erosion and eventual failure.

湍流-切割管道時留下的毛刺使流體產生旋轉作用，導致局部侵蝕，從而最終造成故障。

A closing wedge can be created with use of sequentially larger burrs , with the opposite cortex and periosteum left intact.

閉合楔形可用連續的、大的鉆頭形成，留下完整的對側皮質和骨膜。

If the tank is made of sheet steel, clean it thoroughly to remove all dirt, chips, and burrs.

如果坦克是由鋼板，清洗徹底去除污垢、薯片、毛刺。

Slide shaft into bearing bore, shaft must be straight, true and free of nickes and burrs. proper aligned in the housing.

將軸穿入軸承內孔，要保證軸必須直、正、無毛刺。

To facilitate customer manipulation, strips of stainless steel are rolled to smooth the edges and remove any burrs.

為了方便客戶的操作，軋制不銹鋼帶以使表面光滑，去除毛邊。

Second, obtains closed but including burrs contour lines by using contour lines connection and deformed dilation.

其次采用邊界連接及變形膨脹方法，得到完全閉合、但存在多余毛刺的區域邊界；

The inside and outside surface of casting shall be smooth, sands, oxides and burrs on the un machined surface shall be removed.

鑄件的內部及外部表面應平滑，砂粒，氧化物及毛刺在進行機械加工前應該去除。

The silkscreen should be clear , without burrs and sharp edges, and the dimension is accurate.

絲印必須清晰，無毛刺，尖角，尺寸必須準確。

The crimp shall be generally symmetrical with minimal burrs .

通常卷邊應于最少毛邊對稱。

The main defects are deformation and burrs of cutting surface in the square pipe end.

切口變形和毛刺是矩形管管端的主要缺陷。

An electromagnetic punch, however, stamps its hole without tearing the metal, which means no burrs are left behind, and it never gets blunt.

EMP機床加工，由于再沖孔時不撕裂金屬，所以不產生毛邊，并且從來不會變鈍。

The silk-screen should be clear, without burrs, and the dimension should be accurate.

尺寸準確，絲印清楚，不能有毛邊。

After forged steel workpieces are remove burrs, coarse grinding cutting etc.

鍛后鋼錠去毛刺、粗磨、切割等。

Rough edge paper burrs, paper thin, drizzied conservition, was pale yellow, there is no anti-moisture performance, better ink absorption.

毛邊紙毛邊紙紙質薄而松軟，呈淡黃色，沒有抗水性能，吸墨性較好。

Remove all slivers and burrs left cutting the tube, by reaming and filing, both inside and outside.

通過內外鉸銼，將遺留在管道切割口的長條和毛刺清除掉。

Parts to be clean ad free of MFG oll, burrs, and sharp edges.

工件應該保持清潔，沒有MFG油，毛刺，銳邊。

In this case, the researchers created burrs that stuck to proteins found in the lining of blood vessels.

這種情況中，研究人員生產粘附于血管內膜中發現蛋白質的毛刺。

These units are specially suited for the removal of strong burrs and intensive radiusing of small to mid-size parts.

這些部件特別適于強大的毛刺的移動和使中間集中的尺寸部分成弧形。

Also check that the adjoining pipework is clean and free from debris and burrs.

也檢查所連接的管道是否清潔，沒有碎片和毛刺。

Appearance: No harmful flaws, cracks, burrs, bends and other harmful defects permitted.

外觀：劃痕，裂紋，毛邊，褶皺，此類嚴重的缺陷不接受。

The centers must be aligned and the mandrel must be free of burrs.

這些中心點必須排列成一行，并且保證心軸上沒有毛刺的現象出現。

Check for loose dowels, shims, burrs, dirt between surfaces, etc.

檢查零件表面之間是否有脫落的銷釘，墊片，毛刺，灰塵

Clean and inspect ring gages for nicks and embedded metal filings and burrs.

清洗檢查環規的劃痕和陷入的金屬鐵銷、毛刺。

Stacking of thin specimen is permitted provided they are that, parallel, and from dust or burrs .

在彼此平行并且沒有灰塵和毛刺的條件下，允許重疊薄樣品。

There are usually burrs in the fracture of thin sheet parts stamped with steel blanking die.

用常規鋼制沖模沖裁薄片零件，斷口常有毛刺。

high precision. all edges without burrs, brake sharp edges.

精度高。所有的邊去毛刺，去倒角。

Removing scratches or burrs for welding side of hairline.

拉絲表面焊接后的去劃痕及毛刺。

Requirements for coating is 2, smooth without burrs and blistering, leather, etc.

請求鍍層黑地很光潔，無毛刺及起泡、起皮等本體。